Action Figure NECA Trick ‘r Treat – Ultimate 7-Inch Scale Sam

Collector Freaks Forum

Help Support Collector Freaks Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

K1LLJOY

Super Freak
Joined
Jun 20, 2013
Messages
1,448
Reaction score
924
NECA Trick ‘r Treat – Ultimate 7-Inch Scale Sam


From the delightfully deranged 2007 cult classic film Trick R Treat, Sam joins NECA’s Ultimate line!

The mysterious trick-or-treater gets a deluxe release with all-new, highly articulated body and accessories galore, including 4 interchangeable heads, 2 Jack O Lanterns (one lights up!), interchangeable hand, severed hand, trick or treat sack, lollipop, and candy bar knife. Sam stands approximately 5” tall. Blazing Jack O Lantern uses button cell batteries, included.

Display-friendly window box packaging with opening flap.



NECA-Ultimate-Sam-001.jpg
NECA-Ultimate-Sam-002.jpg
NECA-Ultimate-Sam-003.jpg
NECA-Ultimate-Sam-004.jpg
NECA-Ultimate-Sam-005.jpg
NECA-Ultimate-Sam-006.jpg
NECA-Ultimate-Sam-007.jpg
NECA-Ultimate-Sam-008.jpg
NECA-Ultimate-Sam-009.jpg
NECA-Ultimate-Sam-010.jpg
NECA-Ultimate-Sam-011.jpg
NECA-Ultimate-Sam-012.jpg
NECA-Ultimate-Sam-013.jpg
NECA-Ultimate-Sam-014.jpg
NECA-Ultimate-Sam-015.jpg
NECA-Ultimate-Sam-016.jpg
NECA-Ultimate-Sam-017.jpg
NECA-Ultimate-Sam-018.jpg
NECA-Ultimate-Sam-019.jpg
 
I have just purchased a couple of Neca Trick r Treat Sam figures to give my son at Christmas. I got the clothes figure and the ultimate Sam figure.
I thought I would make him a display base for it to look like this scene in the movie...
 

Attachments

  • TRT-9982.jpg
    TRT-9982.jpg
    1.2 MB
I started out by downloading an image of the wallpaper, then I estimated the hight it should be based on the size of the figure.
I then had the wallpaper printed as a 10 x 8 inch photo.
I had a couple of sheets of 5mm thick acrylic plastic cut to size, glued the photo to the wall section and sprayed it with many coats of satin clear lacquer to seal the photo. This worked very well and has sealed the photo to the wall section with a very durable waterproof finish.
I used jumbo lollipop sticks for the floorboards, weathering them with ash from my log burner, before spraying them with Tamiya clear coat to seal them. I then glued each plank onto the floor section.
 

Attachments

  • IMG_20241202_133722.jpg
    IMG_20241202_133722.jpg
    3.1 MB
Here are a couple of photos with the figure stood on the base.
I have a small wooden side table on its way to me to sit the pumpkin on.
 

Attachments

  • IMG_20241203_003056.jpg
    IMG_20241203_003056.jpg
    3.8 MB
  • IMG_20241203_205035.jpg
    IMG_20241203_205035.jpg
    2.4 MB
I was concerned that the acrylic sheet may warp, so I cut some aluminium L profile and glued it around the sheet with epoxy resin. This will prevent the acrylic sheet from bending/warping in any direction.
I think it also gives the display a nice finished look as well.
 

Attachments

  • IMG_20241207_182737.jpg
    IMG_20241207_182737.jpg
    1.8 MB
  • IMG_20241207_182231.jpg
    IMG_20241207_182231.jpg
    3.8 MB
  • IMG_20241207_182245.jpg
    IMG_20241207_182245.jpg
    3.4 MB
Here is the other figure, which is sealed, so I couldn't try it on the base with it being a Christmas present. I think it will work with the display base though, even though this figure is larger than the other one
 

Attachments

  • IMG_20241205_214634.jpg
    IMG_20241205_214634.jpg
    3.6 MB
Back
Top