1/6 INART (Queen Studio) - The Dark Knight - Joker Collectible Figure

[jsgord58]

Have you tried this? It's not hard and should take you no more than 5 minutes

I know they aren't the same figure or coat but the method is very easy to understand.

View attachment 653097


View attachment 653098

When you twisted the coat it reminded me of a churro which made me hungry. Being on a diet is so hard.

 

[TheBatman]

Little bit of futzing and posing is the secret to make a figure look good.
It's like going back to childhood for a moment, just relax and enjoy playing with your toy.

Just a little bit gentler than when you were a kid tho.
View attachment 653183
View attachment 653184

WOW!!!!

 

[nm.ct]

When you twisted the coat it reminded me of a churro which made me hungry. Being on a diet is so hard.

When hunger comes, drink a ton of water. Works every time

Also not my video haha

 

[DiostaR]

 

[BrooklynWolf X]

Yeah I've seen pictures that make this thing look like trash. One bad pose, one bad angle and it's all over. The best photos make this look like a mini human. Those pics above are amazing and I'd argue the jail sclupt has a stronger likeness to heath than the stock one.

The one thing I see the most in those photos is a narrow/squished head, thus making his eyes appear closer than they really are. Then a few posts later and you’ll see a more flattering photo where he looks…well, normal and amazing.

Just weird as hell.

 

[BrooklynWolf X]

View attachment 653226View attachment 653227

GOT DAMN dude, that’s incredible!

 

[DiostaR]

GOT DAMN dude, that’s incredible!

Thank you.

 

[Chronos1919]

Reached out to SF to see where this guy was at... yet again. Was told they were in the process of shipping last week and now this week that it will be a few more weeks. Don't think I'll be pre-ordering anything else from them.

 

[Pikeroast]

Reached out to SF to see where this guy was at... yet again. Was told they were in the process of shipping last week and now this week that it will be a few more weeks. Don't think I'll be pre-ordering anything else from them.

Dang that’s rough, getting more and more anxious about my Gandalf from them now

 

[ScoobyDoo]

FINALLY!

Now question time:
The head for the purple coat body is very loose fitting, is it supposed to be that way? I can lift up the jail cell joker by his head and it’s fine, but if I even touch the purple coat version the head wants to fall off, it’s just held on my the shirt collar.

And the arm joints for the jail cell version are very squeaky, like a cheap *** third party figure. Is it supposed to be that way? the purple coat version is normal.

 

[bangooface]

Reached out to SF to see where this guy was at... yet again. Was told they were in the process of shipping last week and now this week that it will be a few more weeks. Don't think I'll be pre-ordering anything else from them.

Mine arrived today from SF. Only thing is I’m currently out of town until next week.

 

[Gipetto0812]

Now question time:
The head for the purple coat body is very loose fitting, is it supposed to be that way? I can lift up the jail cell joker by his head and it’s fine, but if I even touch the purple coat version the head wants to fall off, it’s just held on my the shirt collar.

The neck joint on the body of the purple coat has a plastic riser/ring to allow the head to sit a bit higher since it has all the layers on. B/c of this, the magnets don’t make full contact with each other, therefore the connection feels weaker. You can remove the riser however as it’s not permanently attached to get a more secure fit. It’s not a defect though.

 

[KingGrayskull]

The neck joint on the body of the purple coat has a plastic riser/ring to allow the head to sit a bit higher since it has all the layers on. B/c of this, the magnets don’t make full contact with each other, therefore the connection feels weaker. You can remove the riser however as it’s not permanently attached to get a more secure fit. It’s not a defect though.

Alternatively measure the gap and add a neodym magnet there.

 

[Godfather1408]

Also note the neck plug connects a certain way to the head, had to point that out to someone on Facebook.

 

[ScoobyDoo]

The neck joint on the body of the purple coat has a plastic riser/ring to allow the head to sit a bit higher since it has all the layers on. B/c of this, the magnets don’t make full contact with each other, therefore the connection feels weaker. You can remove the riser however as it’s not permanently attached to get a more secure fit. It’s not a defect though.

Thank you, it’s ok as long as I don’t touch the figure, if it bothers me too much I’ll give this a shot!

 

[Gipetto0812]

Alternatively measure the gap and add a neodym magnet there.

Also note the neck plug connects a certain way to the head, had to point that out to someone on Facebook.

yup exactly and good point There's a a notch and key so to speak for the way the head connects to to the neck joint.

 

[jsgord58]

Spec Fiction has 1 sculpted hair premium in stock ready to ship. Wouldn't it be something if a person were to buy it and have it shipped before a person's who ordered this a long time ago?

 

[Earth 616 Collector]

Got my Standard InArt Joker delivered today. Just wow! Even the Standard was an incredible unboxing experience. That's what every 1/6 packaging should be like. All the accessories are great quality (except for the knife). The paint apps on the face, hands, and gloves are a work of art. The tailoring is exquisite. The sculpted hair looks great in hand, much better than I had anticipated from a lot of the pictures.

I have very strong magnets in my stand and wrists. Upsidedown test holds strong. Mine has no trouble holding the diecast weapons. Just make sure the hands are pegged in all the way and you get a strong magnetic hold. I need to futz with the neck connector more to get my final thoughts on that

My only negative so far is the PERS system and the eyes in general. I need to do the PER deconstruction on mine. With the eyes, I think the spacing is just fine. It's the pupils maybe being too large and a little flat. Definitely worth the wait and looking forward to many more InArt unboxings.

 

[ScoobyDoo]

Brothers!
I’ll have the DX 11 with the laughing head from now on, and maybe I’ll take the purple coat off and just have him in the gray jacket. 3 jokers in 3 different looks!
And yes, my DX11 has some missing paint on his nose. It’s Batman’s fault (but he took a dive off my table outside a few years ago and I never bothered to fix it with paint.)

 

[Mr.Tanker]

Got the shipping notice for mine, and I noticed that SpecFiction have the sculpted in stock for $400
https://www.specfictionshop.com/products/joker-sculpted-hair-inart-one-1-6-scale-figure