- Joined
- Oct 31, 2014
- Messages
- 13,003
- Reaction score
- 4,492
Let's get a Black Series X-wing in scale with the Snowspeeder! May the 4th right around the corner...
Hasbro 6" Black Series Star Wars line
- Thread starter Craig77
- Start date
Help Support Collector Freaks Forum:
Hasbro is a bit ahead with it and the VC Fett, figure BBTS probably will be too, I have both on order and haven't gotten notice yet, so just curious if I should be on the lookout.
Hopefully they fix the Fett helmet. All the pictures I’ve seen of in hand photos have the helmet like squeeze together and warped. Looks not so good. I suppose it’s because they glued the helmet on a “head” which squeeze the helmet to adhere.
The problem is how he’s packaged, it’s super tight and it’s soft material. I was disappointed with Beskar Mando for the same reason, if it were a hard plastic head it’d look better, the Vintage Fett head looks fantastic.
Lordscum
Super Freak
if that's the case then I will be sending mine back.
I’ve been seeing people post on YouTube their Bo Katan wave finds in the wild. Anybody find them in your area yet? I’m not holding my breath where I live.
Watch out though..some say the wave might be street dated for April 1
Watch out though..some say the wave might be street dated for April 1
jye4ever
Broke and happy
Everyone is getting a squished Fett helmet WTF Hasbro stop that design asap, I canceled my BBTS order screw that noise
Lordscum
Super Freak
I wish I did, but didn't find out about it until tonight. I will send it back as soon as I get it.
cerealkeller
Super Freak
Re: Hasbro legends 6" sw figures
Heat it up and the shape comes out right away. Not that big of a deal to fix, nothing to cancel over unless it?s out of principle.
Sent from my iPhone using Tapatalk
Heat it up and the shape comes out right away. Not that big of a deal to fix, nothing to cancel over unless it?s out of principle.
Sent from my iPhone using Tapatalk
jimjimmyjones85
Super Freak
- Joined
- Jul 15, 2009
- Messages
- 20,389
- Reaction score
- 127
Re: Hasbro legends 6" sw figures
Does it pop on it's own? Or do I need to stick a screwdriver and pull it out some?
Does it pop on it's own? Or do I need to stick a screwdriver and pull it out some?
Unfortunately, Hasbro made it as a soft helmet that goes over a faux head inside, which is what allows the helmet shape do deform. A user on Instagram cut off the nose to help the helmet keep shape. Since it's not a true head underneath, it should have just been a solid plastic helmet that retained the shape. Either that option was more costly so they cheaped out, or they thought they needed to do it this way to give value to a collector figure. Either way, shame on them for putting out a collector figure that pales to it's 2" smaller counterpart.
Since I want the helmet to look good, I was thinking of both reshaping it with heat and then filling in the gaps inside with magic sculpt so it'll permanently keep shape.
Since I want the helmet to look good, I was thinking of both reshaping it with heat and then filling in the gaps inside with magic sculpt so it'll permanently keep shape.
Lordscum
Super Freak
Re: Hasbro legends 6" sw figures
What method would one use to heat the figure , boiling water or a hair dryer?
What method would one use to heat the figure , boiling water or a hair dryer?
cerealkeller
Super Freak
Hasbro 6" Black Series Star Wars line
I used a hair dryer for about 30 seconds on low. I then sort of pinched from the back and the front and held that for about a minute. Here is my result and while not perfect (Mafex still wins the helmet) it?s a great figure on its own.
Out of the box:
Heat up for 30?seconds:
After sitting for a couple of minutes:
Sent from my iPhone using Tapatalk
I used a hair dryer for about 30 seconds on low. I then sort of pinched from the back and the front and held that for about a minute. Here is my result and while not perfect (Mafex still wins the helmet) it?s a great figure on its own.
Out of the box:
Heat up for 30?seconds:
After sitting for a couple of minutes:
Sent from my iPhone using Tapatalk
Last edited:
cerealkeller
Super Freak
This feels like a good option. If you look at my second and third picture, the shape gradually goes to a shape that while better than out of the box is still not accurate to the shape that I want. Using some sculpt may be the answer to fill in the gap to keep the desired shape. However for those who are cancelling if you?re happy with how mine looks in the third picture, keep your preorder, hit it with heat for 30 seconds then pinch it and honestly it?s more than worth it imo
Sent from my iPhone using Tapatalk
jye4ever
Broke and happy
Nope still looks squeezed
cerealkeller
Super Freak
Hasbro 6" Black Series Star Wars line
One more time with heat and reshape:
This is perfect for me and took less than 5 minutes total.
Mafex Boba can enjoy the rocket blasting pieces Hasbro Boba comes with. This is after an hour of sitting so this is how the helmet stayed:
Sent from my iPhone using Tapatalk
One more time with heat and reshape:
This is perfect for me and took less than 5 minutes total.
Mafex Boba can enjoy the rocket blasting pieces Hasbro Boba comes with. This is after an hour of sitting so this is how the helmet stayed:
Sent from my iPhone using Tapatalk
Last edited:
That's how it should be, Boba's helmet flares, so many sculpts over the years have missed that, always made the Medicom RAH stand out for me.
I can't get over why most of Hasbro's figures lately are so shiny on their "clothes".
cerealkeller
Super Freak
That?s one part that does bother me a bit. Not enough to have to fix currently but I may look at that in the future. I?m just happy the helmet turned out fine if you?re willing to do a simple fix. We should not have to fix it to begin with but it?s better than a solid helmet that cannot be reshaped IMO.
Sent from my iPhone using Tapatalk
Yes, better to have something that can at least be worked better than something that is done forever wrong.
Similar threads
