Sideshow Hoth Han Solo (Echo Base)
- Thread starter Darkarn009
- Start date
Help Support Collector Freaks Forum:
galactiboy
OT Preferist
I was suprised how the fur trimming looked in person, in photos it looked pretty awful but in person it looked good.
Any tips on properly tying the scarf? When I undressed Han I didn't pay attention to how it was tied and now it doesn't look right
Any tips on properly tying the scarf? When I undressed Han I didn't pay attention to how it was tied and now it doesn't look right
It's like the DX Jack Sparrow sash all over again.
Mad Old Lu
Super Freak
Finally got Han and I'm very happy with it except I got the 1.0 body with the longer neck. It does look okay when he's all suited up, but you can see how short the torso is when you take the coat off. Took off the Bespin jacket and it helps a lot with how the coat fits.
Off to lunch now but I'll try and take some pictures today and write some more about him later. But overall I'm very happy with the figure.
Off to lunch now but I'll try and take some pictures today and write some more about him later. But overall I'm very happy with the figure.
Is it easy to swap the necks on these? Just boil and pop? I switched the Han/Luke bodies but they're still about the same height.
I think Luke looked fine on the 1.1, though the vest was really tight and the snaps were being pulled (not happening on the 1.0). I think Han, however, is much improved on the 1.1. Upper body looks better.
I think Luke looked fine on the 1.1, though the vest was really tight and the snaps were being pulled (not happening on the 1.0). I think Han, however, is much improved on the 1.1. Upper body looks better.
- Joined
- Mar 13, 2010
- Messages
- 28,004
- Reaction score
- 31,973
Yes, that's the easiest method. I've been boiling and popping lots of boots and body parts over the last two days!
Fill a mug with boiling water and dunk him neck first in it and wait about a minute. Then with an oven glove it's easy to pull the neck off.
TonTon said:
There's some dark arts at work with these figures. None of it really makes any sense!
^^thank you. Maybe I'll give it a go this weekend. I swapped the bodies upon immediately receiving Han, then wasn't crazy about the 1.0 on Luke and switched them back, then realized the 1.1 was much better on Han than the 1.0 so swapped them back again. Ha! I'm not sure who mentioned this but my 1.0 came with a shorter left leg too, seemed to be something weird at the hip joint. Definitely some dark arts indeed.
- Joined
- Mar 13, 2010
- Messages
- 28,004
- Reaction score
- 31,973
TonTon said:
Mine had a longer right leg. The left one had all the joints seated correctly, but the right knee was pulled out and stuck fast. Pulling the left shin down evened them up and left him permanently taller!
Pixelpiper
Super Freak
It seems like the easiest fix is to just get at least one Tauntaun, put one of the figures on it and forget about any body swaps.
Yup! That was clearly sideshow's plan for using any old body.
Arm gauntlets fixed. That was really bothering me.
This is the pose I went with also
Once again, no complaints aside from the antennae not fitting snugly
galactiboy
OT Preferist
It's funny, regardless of what body they're on they still look really good. I just assumed Han was on a 1.1 as his proportions looked good out of the box, but then it turned out it was a shorter body
And I had a similar experience with the height... Luke on a 1.0 was shorter than Han on his 1.0, and not just the head height, his shoulders were higher than Luke
It is all very odd
And I had a similar experience with the height... Luke on a 1.0 was shorter than Han on his 1.0, and not just the head height, his shoulders were higher than Luke
It is all very odd I was suprised how the fur trimming looked in person, in photos it looked pretty awful but in person it looked good.
Any tips on properly tying the scarf? When I undressed Han I didn't pay attention to how it was tied and now it doesn't look right
Yeah, if you pull all the fur out and really work with it, it can look pretty good. In the earlier pics it almost looked like straw. Giving it a brush to even it out before you futz does seem to help. Not that I brush dolls.
It's funny, regardless of what body they're on they still look really good. I just assumed Han was on a 1.1 as his proportions looked good out of the box, but then it turned out it was a shorter body
And I had a similar experience with the height... Luke on a 1.0 was shorter than Han on his 1.0, and not just the head height, his shoulders were higher than Luke
Yeah, it is really weird given they have the same boots and headgear. Even stranger, laid side by side the 1.0 and 1.1 seemed the same height, but I know they aren't. But I've noticed this before that body heights can depend on the way the joints are oriented/sitting and a figure can vary in height by a fair amount just due to the way you futz the body.
DARTH-THRASHER
Freaked Out
- Joined
- Feb 16, 2010
- Messages
- 103
- Reaction score
- 4
james the cat
Super Freak
- Joined
- Feb 13, 2015
- Messages
- 771
- Reaction score
- 187
I've done hoth now, starting to look at bit clustered lol
Unless hot toys do them further down the line
Wow, the snow weathering on the blue coat looks freakin awesome.
- Joined
- Oct 11, 2006
- Messages
- 8,616
- Reaction score
- 302
Is that a pro type? What color is that coat?
DARTH-THRASHER
Freaked Out
- Joined
- Feb 16, 2010
- Messages
- 103
- Reaction score
- 4
It's a Kenner 1.0 body with blue coat. Belt and pants from 1990s Hasbro Han Hoth, boots from 1990s Hasbro Bespin Luke (dyed), Goggles from Six Million Dollar Man and finally Scarf from the NEW Sideshow Han Hoth
Vonhahn
Super Freak
- Joined
- Nov 28, 2005
- Messages
- 1,031
- Reaction score
- 236
For anyone bothered as much as I was about how loose the leg strap is...but you can't quite bring yourself to cutting and re-gluing it...they this simple trick first...
1) Get you a twisty tie from any other figure you may have laying around
2) Take the blaster out of the holster....put the tip of the twisty tie up from the bottom and catch the strap as it loop inside the holder bottom
3) Pull the slack down through the bottom just a snig.....
4) clip off the extra length until you have just enough to be a brace to keep the slack snug...but not enough to show
That's it. You can decide for yourself it if looks good or not.....
For what it's worth.....
1) Get you a twisty tie from any other figure you may have laying around
2) Take the blaster out of the holster....put the tip of the twisty tie up from the bottom and catch the strap as it loop inside the holder bottom
3) Pull the slack down through the bottom just a snig.....
4) clip off the extra length until you have just enough to be a brace to keep the slack snug...but not enough to show
That's it. You can decide for yourself it if looks good or not.....
For what it's worth.....
Similar threads
