Johno13, good, bad and ugly of my builds so far

Collector Freaks Forum

Help Support Collector Freaks Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Did a bit more to the YubNub stomper
 

Attachments

  • 332050426_585124153491724_5540474247185013729_n.jpg
    332050426_585124153491724_5540474247185013729_n.jpg
    56.4 KB
Yes the armour is printed and I made the stormtrooper under suits, the Tank trooper under suits might be homebrew or I might have replaced them at that point
What material did you use for the undersuits ? Some stretch fabric? 3d printers are the best that could happen to custom freaks,even though they are not cheap. Did you get data sets for the armor?
 
I use 4 way stretch fabric (it was a black seat cover off ebay, sold as a wedding reception seat cover). If I buy an armour file it's generally a 1:1 scale set that I modify for 1/6, the first style of armour is usually the hardest as your setting up the scale and fit for the body your using but now I'm set up to army build R1 and ANH Stormtroopers I modelled my own sandy pack bits so I can do any of the (4 ?, can't remember it's been a while since I deep dived them) packs. I commissioned a 1:1 snowtrooper helmet years ago so that served well as a base for Veers and Ferrix Troopers. 3d printing is awesome and a game changer but theres still room for the old techniques, I've been printing for over 10 years now with fdm then started with resin when the Photon cam out, my latest kick is Lars line up droids but I just got a load of SS R2 units off TheSonofDengar / Kash so I'll be printing new heads for a few, but one's getting a servo stuffed up it's bum to make his head spin in the back of an X Wing
 
This is working at a pro level. Your prints look awesome. Yeah,scaling down to 1/6 makes sense. I especially like the Veers helmet,I wish they would finally give us that one in1/6. Sadly I neither have the space nor the ability to try something like this. Can’t wait to see more off your great work,it’s a pleasure to see what you are putting out there. Good luck with that spinning head
I use 4 way stretch fabric (it was a black seat cover off ebay, sold as a wedding reception seat cover). If I buy an armour file it's generally a 1:1 scale set that I modify for 1/6, the first style of armour is usually the hardest as your setting up the scale and fit for the body your using but now I'm set up to army build R1 and ANH Stormtroopers I modelled my own sandy pack bits so I can do any of the (4 ?, can't remember it's been a while since I deep dived them) packs. I commissioned a 1:1 snowtrooper helmet years ago so that served well as a base for Veers and Ferrix Troopers. 3d printing is awesome and a game changer but theres still room for the old techniques, I've been printing for over 10 years now with fdm then started with resin when the Photon cam out, my latest kick is Lars line up droids but I just got a load of SS R2 units off TheSonofDengar / Kash so I'll be printing new heads for a few, but one's getting a servo stuffed up it's bum to make his head spin in the back of an X Wing
.
 
I bought a frikin Layzor, sadly no shark to mount it on though. Going from my low level 3d modelling skills to 2d and lightburn was not as difficult as I was expecting, still a learning curve but it's a gentle one so far. Managed to draw up the files for a few DS style walls. Doing myself 9 to run across a 180cm shelf might cut it to 7 and a door though.
 

Attachments

  • 353644061_1919601475073025_4177989619945556925_n.jpg
    353644061_1919601475073025_4177989619945556925_n.jpg
    174.1 KB
  • 353632281_1919436591756180_5834447295657615868_n.jpg
    353632281_1919436591756180_5834447295657615868_n.jpg
    128 KB
I bought a frikin Layzor, sadly no shark to mount it on though. Going from my low level 3d modelling skills to 2d and lightburn was not as difficult as I was expecting, still a learning curve but it's a gentle one so far. Managed to draw up the files for a few DS style walls. Doing myself 9 to run across a 180cm shelf might cut it to 7 and a door though.
Wow,that will look awesome. Hope you get it done the way you wish. Can’t wait for the result
 
Woah! What laser did you get? Is it an affordable option for custom work? Great job!
 
Still got lots to do. Another 3 walls, an end for the left side, electrics (was gonna put a screen in but the ones I have are too small), mesh, top and polish the floor to name but a few. Oh and paint, thats just primer and needs a grey blue painting but I'm looking for rattle can as airbrushing all that will be a pain
 

Attachments

  • 355663309_1307778290177580_2904859367539146160_n.jpg
    355663309_1307778290177580_2904859367539146160_n.jpg
    220.5 KB
  • 355664108_1925151307851375_8021474178972442508_n.jpg
    355664108_1925151307851375_8021474178972442508_n.jpg
    184.3 KB
Finally getting round to doing myself some Sand Troopers. Sideshow place holder but I'm starting with Move Along, Got a lid of solobones, I've dialled in my laser for the leather Pauldrons and I think I have the forearms the right shape because of Bones too. Printed armour, pack and I'm going to try to get the weathering as close as I can to the 1:1 prop
370603623_1757039768097320_7535811463018622207_n.jpg
370597574_3484372995153899_5936409030977062981_n.jpg
371494221_841780053998272_3322459805131412155_n.jpg
 
Back
Top