J3D1_KN1GHT
Super Freak
I've seen the the neck joint snap in half before so gan canny!
Metal Gear Solid Collectibles
- Thread starter Rock83
- Start date
Help Support Collector Freaks Forum:
Did you have issue with the railgun arm bearing the weight of it? Like when you click it up with it attached did it take a few tries before you got it? Mine tumbled constantly until I found the right position.
Uncanny Web-Slinger
Super Freak
I can't get it to move much because of the rubber tube underneath.
I actually thought you got it but after seeing the pics again I see that you weren't able to. If you get the tube through the port that it's in you should be able to move it up so that the arm is in the "up" position.
Uncanny Web-Slinger
Super Freak
Okay, i thought you meant when it was horizontal that it dipped or something.
My back pack dips to the right since the extra weight from the rail gun. Is your jaw crooked at all? And my jaw doesn't close flush all the way, it stays slightly open 
Uncanny Web-Slinger
Super Freak
The jaw stay open by like a milimeter or so.
Backpack doesn't look to be dipping.
Jaw doesn't look crooked, perhaps a teeny bit to the side.
I was going to have this in my biggest display cabinet, but because of the rail gun it wouldn't fit
Next i put it on mt Desk next to my Mac and it just looked to cramped, so for now it's on top of my Detolf.
Need to pick ip some batteries tomorrow.
Backpack doesn't look to be dipping.
Jaw doesn't look crooked, perhaps a teeny bit to the side.
I was going to have this in my biggest display cabinet, but because of the rail gun it wouldn't fit
Next i put it on mt Desk next to my Mac and it just looked to cramped, so for now it's on top of my Detolf.
Need to pick ip some batteries tomorrow.
The jaw stay open by like a milimeter or so.
Backpack doesn't look to be dipping.
Jaw doesn't look crooked, perhaps a teeny bit to the side.
I was going to have this in my biggest display cabinet, but because of the rail gun it wouldn't fit
Next i put it on mt Desk next to my Mac and it just looked to cramped, so for now it's on top of my Detolf.
Need to pick ip some batteries tomorrow.
My jaw isn't TOO bad but it is slight and noticeable. I think it's common for the crookedness and the fact the mouth doesn't close. A lot of peoples in-hand photos all look the same with the issues.
I warn you about the railgun, it's BRIGHT
EDIT: How much of the panels have you removed? There are some that are not even described in the instructions such as the top panel on the Radome, not the dish but the hull behind it. And you can remove the panel off a support strut on the left leg. Radtoyreview is a good guage of how much can come off, that's how I found it out anyway.
There was still wet paint on one of the plugs for the outside armor panel of the left leg, it's no big deal and it's dry now but the finish is a flawed now... damn
How easily does your missile hatches fall off? The knee covers aren't too bad for me, but I can literally blow air slightly on the back page and all 8 latches jostle off
Last edited:
Been lurking around and checking out everyone's 3A Rex. So impressed by the size of it and I always feel electronic makes things better!
Unfortunately, having never spent over £300 on any one collectible, I've had to settle for the 1/100 Kotobukiya kit. And not having the paint skills of rampagesss, I've just went for a straight build w/ panel lining.
Great kit to build, an out-of-box snap together would probably only take a couple hours, took me longer for panel lining due to the amount of detail even at this scale.
Joints are tight but there are anumber of parts like the hip guards and external missiles that come off too easily while I overpaid for this due to high shipping even at SAL and a hefty customs charge...
Hope Koto make a MG Ray though!
Unfortunately, having never spent over £300 on any one collectible, I've had to settle for the 1/100 Kotobukiya kit. And not having the paint skills of rampagesss, I've just went for a straight build w/ panel lining.
Great kit to build, an out-of-box snap together would probably only take a couple hours, took me longer for panel lining due to the amount of detail even at this scale.
Joints are tight but there are anumber of parts like the hip guards and external missiles that come off too easily while I overpaid for this due to high shipping even at SAL and a hefty customs charge...
Hope Koto make a MG Ray though!
Hmm... Maybe you can try using some sticky poster tac to keep the panels in place. It sells at Staples for a few bucks.
It won't fit, unless you cut a hole into the detolf cabinet. A few members on ThreeA forum did it, but their REXes looked extremely cramped in the detolfs.
rampagesss
Super Freak
Found this picture on another MGS forum and would love to own this figure!
Metal Gear Kojima
Metal Gear Kojima
^Someone already posted that in the Rising thread. I don't really like how it looks though. The small head-sculpt on that huge body, leaves me with the impression that Kojima is wearing some kind of "fat suit" .
.
J3D1_KN1GHT
Super Freak
He has girl like proportions. Girl.
Found this picture on another MGS forum and would love to own this figure!
Metal Gear Kojima
I like it
Sent from my iPad using Tapatalk HD
rampagesss
Super Freak
Yes you need to paint everything Rex and the figures, Rex isn't to hard
But the figures are crazy small! so i gave up on thoses
Found this picture on another MGS forum and would love to own this figure!
Metal Gear Kojima
dont like it.
Looks like a middle aged lesbian IMO.
Similar threads
