1/6 MMS DX 02 - TDK- BATMAN full spec and pics

Collector Freaks Forum

Help Support Collector Freaks Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Re: Hot Toys - MMS DX 02 - TDK- BATMAN full spec and pics

i don't know myself, but I've heard that it fits in the cape slots just fine, but you'll have to cut off the other clips that attach to the shoulder blades in order for the back pack to sit right on the V1 TDK bats
Cut some parts off? I've to rethink this then. Thanks for the reply.:hi5:
 
Re: Hot Toys - MMS DX 02 - TDK- BATMAN full spec and pics

Forgive me for going a little off topic, but the original MMS71 thread is locked. The right ankle of mine is really loose. The peg is fully inserted and everything, but it moves up and down with ease and makes it difficult to stand the figure on its own. I tried searching for a solution but could not find any.
 
Re: Hot Toys - MMS DX 02 - TDK- BATMAN full spec and pics

Forgive me for going a little off topic, but the original MMS71 thread is locked. The right ankle of mine is really loose. The peg is fully inserted and everything, but it moves up and down with ease and makes it difficult to stand the figure on its own. I tried searching for a solution but could not find any.

Just wrap a little Plumbers tape around the peg.
 
Re: Hot Toys - MMS DX 02 - TDK- BATMAN full spec and pics

Forgive me for going a little off topic, but the original MMS71 thread is locked. The right ankle of mine is really loose. The peg is fully inserted and everything, but it moves up and down with ease and makes it difficult to stand the figure on its own. I tried searching for a solution but could not find any.

You might want to doublecheck with a flashlight, and make sure you didn't break the socket the peg fits into.
 
Re: Hot Toys - MMS DX 02 - TDK- BATMAN full spec and pics

Just wrap a little Plumbers tape around the peg.

Ooh, good idea! I've never thought of using that!

Another way is to put a thin coating of super-glue on the peg, but the plumbers tape is nice and reversible. :clap
 
Last edited:
Re: Hot Toys - MMS DX 02 - TDK- BATMAN full spec and pics

Ooh, good idea! I've never thought of using that!

Another way is to put a thin coating of super-glue on the peg, but the plumbers tape in nice and reversible. :clap

And no messy adhesive, it just sticks to itself.
 
Re: Hot Toys - MMS DX 02 - TDK- BATMAN full spec and pics

I use nail polish to tighten joints on my figures, works well.
 
Re: Hot Toys - MMS DX 02 - TDK- BATMAN full spec and pics

Anyone else got a problem with the LED lights on their stands?
Feels like mine has a way to short wire between the wich makes it impossible to direct just one light. Move one, and the otvetydigt Will move as well. So I cant put both the lights on the figure. One goes on, the other goes away.

Anyone?
 
Re: Hot Toys - MMS DX 02 - TDK- BATMAN full spec and pics

Had the same problem with my DX stand...either the 01 or 02. The wires are short in there. But they will work if you adjust them a bit. The bottom of the DX stands can be removed. Carefully pry the bottom open and rearrange the wires so that they run the shortest distance from the power source to the lights. That should allow for enough room for you to move one light without the other one moving in the opposite direction.

If your wires are exceptionally short, you can splice one with some extra wire and just lengthen one or both of them.

Hope that helps.
 
Re: Hot Toys - MMS DX 02 - TDK- BATMAN full spec and pics

I figured that there could be such a solution, but I'm such a wuss when it comes to stuff like this, I'm afraid to brake it :p!
But I think I'll try! Thanks :)!
 
Re: Hot Toys - MMS DX 02 - TDK- BATMAN full spec and pics

Had the same problem with my DX stand...either the 01 or 02. The wires are short in there. But they will work if you adjust them a bit. The bottom of the DX stands can be removed. Carefully pry the bottom open and rearrange the wires so that they run the shortest distance from the power source to the lights. That should allow for enough room for you to move one light without the other one moving in the opposite direction.

If your wires are exceptionally short, you can splice one with some extra wire and just lengthen one or both of them.

Hope that helps.

I'm going to try to do this then b/c both my DX01 and 02 stand lights don't turn facing the figure. well it's more of 1 light on each stand won't turn to face the figure but instead off to the side. this may sound dumb, but is there a certain method/tool to use to pry the bottom piece open and will it just pop back on afterwards?
 
Re: Hot Toys - MMS DX 02 - TDK- BATMAN full spec and pics

I just used one of those small flat head screw drivers that usually comes in a box set of 5 or 6. You can buy em at the hobby store, hardware store or computer stores. You could even use the flat head screwdriver that comes in an eyeglass repair kit.

Once you pop it off, you'll see how it goes back on. It's real easy just be careful while prying it off that you don't break any of the holding clips. Once you rearrange the wires, that should fix it right up! Both lights should be able to face the figure simultaneously.
 
Re: Hot Toys - MMS DX 02 - TDK- BATMAN full spec and pics

Good to know. My lights are a little wonky too.
 
Re: Hot Toys - MMS DX 02 - TDK- BATMAN full spec and pics

Could anyone advise me on a fair price range for this piece? One that's MISB. Thanks in advance.
 
Re: Hot Toys - MMS DX 02 - TDK- BATMAN full spec and pics

^^^
understood. But since I want one unopened there's no way to tell.
 
Re: Hot Toys - MMS DX 02 - TDK- BATMAN full spec and pics

^^
I put one of mine up for auction & it sold for £310 + £10 postage but mine had been displayed in a detolf. That was about 6 months ago though before HT announced there new licence, HT will highly likely make this suit again being that it's in Rises so your probably better of waiting for that one.
 
Re: Hot Toys - MMS DX 02 - TDK- BATMAN full spec and pics

^^^
understood. But since I want one unopened there's no way to tell.

Yes there is. It needs to be from the DCD batch. If its not, it will leak 100% for sure

If its from the DCD batch the leaking would be limited to the biceps.

DCD batch MISB one would probably be $500+

Non DCD Batch $350-400 I think
 
Back
Top