Action Figure Obi-Wan Kenobi Mythos Statue Unlit Hilt Interest Thread
- Thread starter furystorm
- Start date
Help Support Collector Freaks Forum:
- Status
Darth Madden
You Are A Tooooooy!!!
Nope, I can tell where the hook SHOULD have been but its just flat.
slynger
Super Freak
I was looking at where the lightsaber is supposed to be and I think I'll be able to use a razor blade and make just enough room for a hook. I think I will go that route, that way I can switch out the pieces like we were supposed to be able to.
Viper245
Super Freak
Darth Madden
You Are A Tooooooy!!!
I'll check when I get home tonight but I'm 99% sure my silver ares is flat with the rest of the statue... no filled in hook at all.
LightSword
Just a little freaky
Thank you for adding my name to the list, for the welcoming and your kind words towards my Obi-Wan set up. As Darth Snoopy mentioned, the painting is a Vanderstelt. It is an AP that I bought directly from Jerry's desk during Celebration here in Florida and he signed it for me.
I just wanted to add I sure appreciate the effort by MYC to provide collectors with this important, left out addition to the Mythos statue. This sure comes to show how our hobby can create such community feel by attracting so many dedicated, honest people willing to help.
* I don't know if this helps but, there is a little bit of material protruding from Obi Wan's lightsaber belt hook that in fact might allow enough room for a thin hilt ring to go over it and hold the piece in place. If need be, I'd even be willing to make more of a gap between the hook and the belt to secure a saber ring over it. It seems doable.
I just wanted to add I sure appreciate the effort by MYC to provide collectors with this important, left out addition to the Mythos statue. This sure comes to show how our hobby can create such community feel by attracting so many dedicated, honest people willing to help.
* I don't know if this helps but, there is a little bit of material protruding from Obi Wan's lightsaber belt hook that in fact might allow enough room for a thin hilt ring to go over it and hold the piece in place. If need be, I'd even be willing to make more of a gap between the hook and the belt to secure a saber ring over it. It seems doable.
What I was thinking of doing is if it came with a ring, I would jsut carefully use a tiny hacksaw blade or razor blade to gentlily "saw" back and forth a little bit to create a tiny separation for the ring to rest in.
These were the best photos I could get of mine. It may seem like some people's hook is filled in more solid.... (if that makes sense)
These were the best photos I could get of mine. It may seem like some people's hook is filled in more solid.... (if that makes sense)
Viper245
Super Freak
Mine looks about like yours costell2 but in my case it doesn't matter since I have to get a replacement body sculpt due to a defect in mine. The new one will more then likely look different.
slynger
Super Freak
Here's mine - I'm thinking a razor blade and some patience will go a long way in having a functional/removable saber hilt.
Viper245
Super Freak
Viper245
Super Freak
When did you contact them?
LightSword
Just a little freaky
Here's mine - I'm thinking a razor blade and some patience will go a long way in having a functional/removable saber hilt.
That's what I've just finished doing with mine, Slynger. But I now can see some folks have their statue with the hook flat against the belt and that could indeed, be an issue. Just for record keeping ...
Using the tip of an Xacto knife, a pocket saw, and a lot of patience, I was able to scrape off some of the excess material behind the belt hook, just enough to allow a small ring ( a key- chain link I used) to sit behind it. While the scale is bigger than what a ring for the hilt will be, the space created now allows to attach the hilt to the hook without the need of gluing it to it.
Darth Madden
You Are A Tooooooy!!!
Yeah, that little gray square under the belt is completely flat on mine.
myc
Super Freak
- Joined
- May 23, 2009
- Messages
- 5,392
- Reaction score
- 13
Just curious if you have received a response yet from Sideshow regarding your replacement request myc? I sent my request on Sunday and still no response.
U contacted them last Friday!!! A whole week without response!! Will call them on Monday.
About the hook... would be interesting if there are really different types out there.
The one from you lightsword looks pretty good and duable to hang on
ExMem-LarjaThwei
Super Freak
- Joined
- Jul 12, 2010
- Messages
- 10,762
- Reaction score
- 18
Not sure if this has been suggested or not, but what about simply sculpting a small piece similar in design to the hook on the prototype and buyers could glue it on to their own statue?
I have no knowledge of sculpting, but to me that seems like the best/most easy way of doing it.
So in the end, you'd be making the hilt with a ring attached to it and then a separate, small hook-like sculpt for the customers to glue on to their statue which they would use to hang the saber hilt ring on.
I have no knowledge of sculpting, but to me that seems like the best/most easy way of doing it.
So in the end, you'd be making the hilt with a ring attached to it and then a separate, small hook-like sculpt for the customers to glue on to their statue which they would use to hang the saber hilt ring on.
Monday afternoon.... March 25th. I got a response from the returns department on Wednesday.
For what it is worth, I called Customer Service and they sent me an email to respond to with pictures. I responded to that email 45 min later. That was then forwarded from the Customer Serivce Rep to the Returns Department. I got a response from them a day and a half later, on Wednesday the 27th.
- Status
Similar threads
