1/6 Hot Toys - Iron Man 3: MMS197D02 Mark XLII Diecast Series Official Spec/Pics

[DarkAngel]

Because they're limited by how much they can do with anything relating to X-Men

 

[Brainiac]

Yea I want to be able to pose this guy - I have seen so many cool options with him.

Yes and doing so without breaking the figure should be possible, and its something that come standard for a $300 figure

 

[DarkAngel]

Yes and doing so without breaking the figure should be possible, and its something that come standard for a $300 figure

If this thing is really breaking that easy, especially after how long of a wait we've had, then its just stupid

 

[AIR]

Amazing Spiderman all over again. Delay after delay, figure finally is released and looks promising in the early pics, reports of shoulders breaking start coming in. I just hope that sideshow gets a better batch

 

[Brainiac]

If this thing is really breaking that easy, especially after how long of a wait we've had, then its just stupid

I'll have to open this to check it

 

[DarkAngel]

I'll have to open this to check it

Or you could not and just live in blissful ignorance

 

[Brainiac]

Or you could not and just live in blissful ignorance

sounds good!

 

[DarkAngel]

sounds good!

 

[Taibhse]

It's kind of ironic that people were so concerned about the die-cast being a production/quality-control issue - and in the end it's a cheap piece of plastic that's causing all of the trouble.

Indeed, wonder if that is why diecast haters have been relatively quiet on this issue....

 

[VincentVegaFFF]

I don't know. ClipperKing did quite a few dynamic poses in his videos, including the landing pose and his joints look good so hopefully the problems are not widespread and the figure can still be posed with some care.

 

[DarkAngel]

I don't know. ClipperKing did quite a few dynamic poses in his videos, including the landing pose and his joints look good so hopefully the problems are not widespread and the figure can still be posed with some care.

Solid point. I had forgotten about that

 

[Brainiac]

I was hoping this would ship this month, My flex ends on the 5th....... and I want to see if these problems are widespread before committing to this figure

 

[El-Vi-Riachi]

Possible it could be a bad batch? Saw this image recently and the difference between the right and left is stark....

 

[AIR]

Possible it could be a bad batch? Saw this image recently and the difference between the right and left is stark....

View attachment 121867

 

[Andrew117]

View attachment 121868

My favourite use of that gif for awhile ahaha

 

[R3d15]

Possible it could be a bad batch? Saw this image recently and the difference between the right and left is stark....

View attachment 121867

which one is the good one?

 

[spindrift]

I'm not panicking....we will see once SS gets them and many of us get theirs...

 

[Brainiac]

which one is the good one?

the left one

 

[R3d15]

Just receive my figure from HK..man i have never been so slow and careful playing with any HT figure..so far so good both on my mk42 arm, moving the arms up and down couple of times now but...i think i got a defect right arm maybe

Sent from my iPhone using Tapatalk

 

[CollectorGuy]

Just receive my figure from HK..man i have never been so slow and careful playing with any HT figure..so far so good both on my mk42 arm, moving the arms up and down couple of times now but...i think i got a defect right arm maybe

Sent from my iPhone using Tapatalk

Woa that looks bad. is this picture legit? It looks the same as all the other pictures of defective joints.
The warping of the plastic in the joint looks the same. I guess im not just being paranoid after all.