1/6 Hot Toys - MMS284 - Avengers: AoU - Ultron Prime Collectible Figure

[SilverStar17]

I also like his Guardians Mini mates display I think Star prince is break dancing and Drax is stabbing Ronan in the back Literally, not metaphorically because that will just go over his head

I noticed that as well. I like Yondu in the back there as well.

 

[Darkseed]

yeah, i'll probably end up with all three (hopefully we get the ultimate version).

the mark 1 is just too creepy and interesting to pass up. plus, it was an awesome scene. and prime is just too large and imposing to pass up.

hopefully ultimate ultron will be the best of the bunch.

Mark I will be tough to pass, creepy is a good word.........prime will suffice for the larger version

 

[jordanimal]

I also like his Guardians Mini mates display I think Star prince is break dancing and Drax is stabbing Ronan in the back Literally, not metaphorically because that will just go over his head

hahahah I didn't even realize that made the cut in my AoU pic!

if u think I ONLY have guardian minimates set up underneath my hot toys...

btw, just made the most minor change, but thought it was worth posting, shuffled around WM, hulk & BW. I think it looks better here

 

[NotDolls]

So I'm sure there is already advice on this somewhere in this thread -- but I wasn't able to find it. But does anyone have any recommendations for getting the darn head light switch compartment open? Mine will NOT budge! I bent the plastic tool attempting to get it open, so I tried switch to something metal. Of course that left some minor scratches (very minor, but I'm still kicking myself) and still no luck! Anyone else have this kind of trouble?

 

[TimothyR]

So I'm sure there is already advice on this somewhere in this thread -- but I wasn't able to find it. But does anyone have any recommendations for getting the darn head light switch compartment open? Mine will NOT budge! I bent the plastic tool attempting to get it open, so I tried switch to something metal. Of course that left some minor scratches (very minor, but I'm still kicking myself) and still no luck! Anyone else have this kind of trouble?

Maybe try a little heat?

 

[Charlie2099]

So I'm sure there is already advice on this somewhere in this thread -- but I wasn't able to find it. But does anyone have any recommendations for getting the darn head light switch compartment open? Mine will NOT budge! I bent the plastic tool attempting to get it open, so I tried switch to something metal. Of course that left some minor scratches (very minor, but I'm still kicking myself) and still no luck! Anyone else have this kind of trouble?

I had the same problem which also caused minor scratches. I broke my plastic tool as well. I used a small thin piece of metal. I used so much force that when it came off it flew across the room. I suggest you find something plastic, small enough to fit, but hard enough that won't break to get it off. Ultron's head didn't break and I used a lot of force. I've found a way on mine to keep it from happening. First I put the back on, then push the front in. I'll pull the front off first when taking it off. I also don't push too hard when putting it back in.

 

[Brainiac]

Maybe try a little heat?

Just a bit, should work

I'd also recommend to anyone who collects these to invest in a good precision screwdriver set

as for the head piece I find that lifting it up and back from the brow/front helps with removal

 

[TimothyR]

I had the same problem which also caused minor scratches. I broke my plastic tool as well. I used a small thin piece of metal. I used so much force that when it came off it flew across the room. I suggest you find something plastic, small enough to fit, but hard enough that won't break to get it off. Ultron's head didn't break and I used a lot of force. I've found a way on mine to keep it from happening. First I put the back on, then push the front in. I'll pull the front off first when taking it off. I also don't push too hard when putting it back in.

Bummer it's not magnetically held in place.

 

[Bjjer]

I used a piece of metal wrapped in tape to prevent scratching. Popped right out.

 

[Charlie2099]

Bummer it's not magnetically held in place.

Good point. Is there a reason HT didn't do that?

 

[TimothyR]

Good point. Is there a reason HT didn't do that?

i don't have it in hand yet.. but i think it's probably because they usually use plug in panels for batteries/switches rather than making them magnetic.

 

[Charlie2099]

i don't have it in hand yet.. but i think it's probably because they usually use plug in panels for batteries/switches rather than making them magnetic.

I don't see how Ultron's scalp is different from Iron Man's faceplate.

 

[Motuxmen]

I don't see how Ultron's scalp is different from Iron Man's faceplate.

we may not know why but there is a reason for the design. My guess is just the design. As thin and curved as it is, with little places to hide a sunken in magnet, there was probably not enough room to do it. There's a big difference between the shape, design, and placement of the ultron scalp and the iron man faceplate.

 

[robbiethepainter]

Still w.i.p but I really dig this guy.

 

[DasMuse]

Spent the better part of an hour this morning posing Prime fighting with Mk 43... Articulation limits kept me from getting it exactly how I wanted, but I'm satisfied with the end result.







Once again i'm sorry for not having a space for taking pictures of figures... I literally have no extra room at the moment, i'm still looking for display cases.

 

[Motuxmen]

No need to apologize. Most people don't have a photo booth/location so it's not something you need to apologize for.
Cool poses though.

 

[goatchumby]

Still w.i.p but I really dig this guy.

Outstanding!

Well, I was rather pleased with Ultron's stock paint...

 

[SilverStar17]

Great pictures!

 

[Newbieguy]

Great pictures!

Local comic book store has one. Hmmmm.

 

[Parvus_Minor]

Spent the better part of an hour this morning posing Prime fighting with Mk 43... Articulation limits kept me from getting it exactly how I wanted, but I'm satisfied with the end result.

View attachment 275619

This angle makes Ultron look like Classic Ultron.

I LIKE WHAT YOU GOT.