1/6 Hot Toys - POTC5 - Jack Sparrow Figure (Artisan Edition + Regular) Collectible Figure

[Godfather1408]

How easy is it putting the DX38 eyes back together?

 

[Cap'n Cook]

How easy is it putting the DX38 eyes back together?

You literally can just pull them out and put them back in.

 

[Godfather1408]

You literally can just pull them out and put them back in.

Not as simple with DX15 just did mine Jesus they glued that plastic in place well.

 

[MaulFan]

The urge to now pop the eyes out of the DX15 sculpt and add them to the DX38.

The darker (“UV contact lenses”) eyes make a huge difference.

Man, it’s tough. The modded DX38 sculpt is much more realistic and it looks pretty. The likeness is better, albeit not perfect. Contrast to the stock DX15 where I think the likeness is still stronger but lesser quality and realism. This is reminding me of the same scenario with the DX09 vs the MMS692/693 ‘89 Batman. IMO, the DX09 is the stronger sculpt overall (more accurate cowl details and better mouth-plate likeness), but it’s dated compared to the new one.

While the angles and such are not the same, I feel like the DX15 has a bit more stern intensity to the face, where the DX37/8/9 is more neutral, I see value in having both heads around, which is why I'm looking around to buy another DX15 smirking to take apart for the eyes to upgrade my DX37/8/9 neutral face.

Now this is tough.

Alright, so which is the better hat? Enterbay or MMS42?

As far as hats go, the right hat is a matter of personal preference. When DX15 came out and I needed a new hat, I went looking for the MMS42 and Medicom RAH hats for mine because I prefer the symmetry of it, the silhouette it creates, etc. Back when we only had the first 3 movies, the look of Jack's hat was pretty much defined by Curse or World's End, he barely had enough in Dead Man's Chest for that movie to leave an impression, and for quite awhile, that meant Curse was the only real reference, and I find that it had a pretty uniform shape throughout that movie. I have never liked how in World's End, the hat has like 100 different shapes throughout because the material they used would fold and bend in different ways from scene to scene and I found it to often look ugly.

For me the worst hat though is On Strange Tides, and only because it looks nothing like Jack's hat in the first 3 movies, the front is too upright and firm, like a brand new hat fresh from the store.

My second favorite hat look is DMTNT. It's a bit more on the pristine side like OST, but the weathering and overall look feel the closest to the Curse hat of all the sequels.

after seeing more of the Enterbay hat, looks like I fu*ked up in going with the MMS42.

The Enterbay hat has more character and kinks in the hat, and the finish is better out the box too, looks more lived in, like the real deal. The only thing I don’t really like is the unsightly mould line running through the front of the hat. What is that? The MMS hat is too “perfect” in its design, which is a bit more reminiscent of how the tricorne hat is supposed to look like in DMTNT.

If you decide to part with your MMS hat, please let me know.

How easy is it putting the DX38 eyes back together?

As you noted, getting to the eyes in a DX15 head is some measure of work because you have to remove the entire housing for the neck joint and eye controls, but on DX37/8/9, they're just sockets to pop in.

The challenge I ran into is popping the new eyes into the head immediately after removing the current eyes. The material was soft enough were you could find yourself bulging the eyes out if you pop them into far. I don't know if you let the head fully cool, how easy popping in would be at that point. I just redid the one eye I was having issues with a few times until it was right.

 

[Cap'n Cook]

You don’t even have to heat the new DX sculpt to get the eyes out. In and out is super easy. Did it on mine several times.

 

[Godfather1408]

Just picked up a DX15 smirk for cheap to use the eyes, put the DX15 neutral back together as I still like that sculpt. The expressions for them are different for sure.

Waiting for Julian's hat to arrive, without taking the sash off any suggestions on making it look more natural?

Wish JND were doing a 1:6 potc 1 instead of 1:4.

 

[MaulFan]

I can't think of anything to do with the sash that doesn't involve removing it. You could try to rough up the fabric and make folds with what's exposed, I just don't know how effective it will be or how long the effect will last.

I soaked mine in water, balled it up and wrapped it in elastics for like a day or two so that it would be nice and wrinkly and all, then tied it using 1:1 scale tutorials.

I also just secured a second DX15 smirk head off eBay, so I'll be upgrading my DX38 neutral as soon as that comes in.

 

[Gipetto0812]

Just picked up a DX15 smirk for cheap to use the eyes, put the DX15 neutral back together as I still like that sculpt. The expressions for them are different for sure.

Waiting for Julian's hat to arrive, without taking the sash off any suggestions on making it look more natural?

Wish JND were doing a 1:6 potc 1 instead of 1:4.

JND is doing a 1/3 scale statue, not 1/4. I wouldn't be surprised if they're also able to do a 1/6 under the Kojun Works line. They just can't reveal both at the same time. It's been many years since their 1/3 TDK Joker was released and only now are they releasing the 1/6 version.

 

[HyperDrive]

I’m just gonna settle with a subpar Jack figure lol. It’s crazy how much I have to mod most of my Hot Toys figures to bring them up to a certain par. I wish INART had these Disney licenses, it’d be the answer.

I’ll have to dump more money to have Raimi Spider-Man and even more for Indiana Jones. Even the T2 T-800 needs the DX10 glasses (if they even fit).

I’m so glad I’m not wasting money on assembling a decent TDK Batman figure currently with all the Armory versions and custom cowls out there (OATY is the best). I’ll just keep waiting for INART and call it a day.