1/6 Hot Toys-MMS 236-TDK Armory (with Batman, Alfred, and Bruce Wayne Figures)
- Thread starter batfan08
- Start date
Help Support Collector Freaks Forum:
Rudimus
Super Freak
- Joined
- Jan 9, 2014
- Messages
- 914
- Reaction score
- 11
Awesome shot gothamcity boy!! & nice cape 北京国安! This figure is a keeper.
gothamcityboy
Super Freak
- Joined
- Jun 6, 2012
- Messages
- 852
- Reaction score
- 3
Thanks Rudimus, still need to mod body little bit though, and yes its a must figure for any batman fan!
asgardianboy
Super Freak
- Joined
- Jan 16, 2016
- Messages
- 1,711
- Reaction score
- 124
Hi there guys.
I got this set, with Alfred and Bruce. It is time for me to open it up, but before I'd like to get as much info about it as possible. I was wondering if any of the savvy freaks who have been partaking on this thread since its beginnings, would be so nice to share with newcomers like me any tip/tricks/issues/fixes/conclusions/best practices regarding this nice Batman set.
To trigger the discussion, I am wondering whether the Batman fig included in this set would be EXACTLY the same as the dx12 one. Is that correct?
I have also heard bad things regarding the mouths of this release not properly fitting into the head slot and that the same worked much better in previous releases. Any truth to this?
Also regarding posing, I am afraid I NEED to pose this guy croaching (knees fully bent) and in dynamic positions, be it fighting or watching over an scene (or the entire Gotham!). I guess I will destroy the rubber outfit if I do so and keep the figure in such positions, right?
Finally, I am considering using this bat to implement other versions of him that have been seen on screen lately. Even though the movies are dull, I am particularly found of the Knightmare version (was it taken from some comic, that look? It's just great!). To save some cash, I am considering the possibility of kitbashing it on top of the version that comes in this armoury set. My most pressing question would be whether you guys think it could be possible to put some OD trousers on this guy, then run them down the lower leg UNDER THE APPARENTLY HYPER-TIGHT UPPER BOOT PIECE. It seems impossible at first sight, because I don't expect it to be flexible (I hope it is not rubber!!), and even if it was, after a long time of extra pressure because of the trousers, the piece would probably be deformed and would never again fit the leg tightly.
With the same aim, I am also wondering whether the gauntlets can be removed, so that I could get the figure inside some coat, then replace the gauntlets.
Thanks for all the info, guys!
m.
I got this set, with Alfred and Bruce. It is time for me to open it up, but before I'd like to get as much info about it as possible. I was wondering if any of the savvy freaks who have been partaking on this thread since its beginnings, would be so nice to share with newcomers like me any tip/tricks/issues/fixes/conclusions/best practices regarding this nice Batman set.
To trigger the discussion, I am wondering whether the Batman fig included in this set would be EXACTLY the same as the dx12 one. Is that correct?
I have also heard bad things regarding the mouths of this release not properly fitting into the head slot and that the same worked much better in previous releases. Any truth to this?
Also regarding posing, I am afraid I NEED to pose this guy croaching (knees fully bent) and in dynamic positions, be it fighting or watching over an scene (or the entire Gotham!). I guess I will destroy the rubber outfit if I do so and keep the figure in such positions, right?
Finally, I am considering using this bat to implement other versions of him that have been seen on screen lately. Even though the movies are dull, I am particularly found of the Knightmare version (was it taken from some comic, that look? It's just great!). To save some cash, I am considering the possibility of kitbashing it on top of the version that comes in this armoury set. My most pressing question would be whether you guys think it could be possible to put some OD trousers on this guy, then run them down the lower leg UNDER THE APPARENTLY HYPER-TIGHT UPPER BOOT PIECE. It seems impossible at first sight, because I don't expect it to be flexible (I hope it is not rubber!!), and even if it was, after a long time of extra pressure because of the trousers, the piece would probably be deformed and would never again fit the leg tightly.
With the same aim, I am also wondering whether the gauntlets can be removed, so that I could get the figure inside some coat, then replace the gauntlets.
Thanks for all the info, guys!
m.
WhoaItsJBot
Super Freak
I'm selling this if anyone is looking. Comes with Alfred and two Batman figures.
At long last, my setup is complete
SilverStar17
Super Freak
Nice! 
Nice!
Thanks! Got a lforignio custom cape that day and now I'm content with it.
Barrow Roll
Super Freak
- Joined
- May 4, 2012
- Messages
- 408
- Reaction score
- 9
Is that cowl something that's going to be for sale? How do I follow progress on it?
master anakin skywalker
Super Freak
- Joined
- Jan 22, 2015
- Messages
- 425
- Reaction score
- 14
This is such a nice picture. I think it’ll be the background picture on my phone.. lol
Sent from my iPhone using Tapatalk
AB next to 1/4 TDKRB
bosefus17
Freaked Out
- Joined
- Nov 4, 2018
- Messages
- 106
- Reaction score
- 1
Hey everyone, so my armory lights won't turn on anymore.
I put fresh batteries in and turned the switch on, but no luck.
I also tried the remote and the lights still wouldn't turn on.
Has anyone else had a similar issue?
Sent from my SAMSUNG-SM-G935A using Tapatalk
I put fresh batteries in and turned the switch on, but no luck.
I also tried the remote and the lights still wouldn't turn on.
Has anyone else had a similar issue?
Sent from my SAMSUNG-SM-G935A using Tapatalk
bosefus17
Freaked Out
- Joined
- Nov 4, 2018
- Messages
- 106
- Reaction score
- 1
I have the DX12. How much better is this Batman than the DX12? And is it worth it if I can get it for it’s original MSRP of $625?
Similar threads
