Hot Toys – MMS132 - Iron Man 2: Mark VI full spec and pics

[vodoun]

If these were actual Lithium cells no, but since these are likely cheap China made ones and someone already post one that popped open ..... maybe I should go remove them all

Hmm... when was this. Mech Test is the most annoying one to take out. Batteries deep below the shirt.

 

[Station]

Have you guys seen this?

Found it at statuemarvels website. I saw you guys posting all the Marks together and I thought I'd share this.

Been PM-ing the guy about where to get that Hall of Armor but the inbox is full.

It looks simplified from the actual hall, but I bet I could make something like that. Looks just like laser cut acrylic for the most part. The back is the only hangup, but it might be doable.

 

[darthjuan007]

I finally finished putting him together. Im going for the BD look right now. It really wasn't that hard but with the fear of breaking him, it did take longer for me anyway.

Took some quick pics of the process but had to hurry as the sun went down so please forgive the last few. I hope it helps somebody with what to expect when they get there own.

Started like this:

Taking the chest plate off:

Surprised that it was held on by magnets:

This was tuff until I read the instructions...take it off at a downward angle.

Sorry this were the sunlight starts to go down

Taking off the thigh plates:

The arm was hard to take off but it finally came off:

 

[darthjuan007]

The BD mask was also held on by magnets:

It took other pics but they came out terrible. I hope this helps somebody when they get theirs.

 

[ebor]

^^^thanks for the photos darthjuan007

 

[ah_t00t]

Hmm... when was this. Mech Test is the most annoying one to take out. Batteries deep below the shirt.

I had some of the batteries popped out even after i removed them upon 1st recieving it.

Yup i totally agree, my gf was like looking at me in a weird way asking what am i doing, lol

 

[bandito]

Surprised that it was held on by magnets:

The one metal plate on the biceps cover fell off and sticking to the lower magnet on the arm. You'll need to super glue it back...

The metal plates on the mask and biceps covers falls off easy.. be careful

 

[dedguy]

yeah I had that problem. I had that problem way back with Abe Sapien's mask too.

 

[The Josh]

My exclusive has shipped and will be here next Thursday.

 

[Centurion]

It looks simplified from the actual hall, but I bet I could make something like that. Looks just like laser cut acrylic for the most part. The back is the only hangup, but it might be doable.

Hmmmm.....
I might be tempted in getting something like that if it looked good enough.

But, yeah, the backdrop should look more like the Hall of Armors in the movie. Not taking anything away from the one in the picture, I do think it looks good, but I'd like it to look closer to the movie version.

Then there's the stands. The Hall of Armors stand that comes with the Mk.IV would look great with your acrylic case, edge-lit, of course.

 

[Centurion]

It took other pics but they came out terrible. I hope this helps somebody when they get theirs.

DJ, that was very helpful bro.
I don't have one yet, but I'll remember this and pull it up when I eventually get mine.

 

[Centurion]

My exclusive has shipped and will be here next Thursday.

Woo hoo!
Not much longer now.

 

[The Josh]

Woo hoo!
Not much longer now.

Yeah, get this and finally add to the fun in this thread. Hate waiting but I'm just a bit ____ in wanting to take all my pics and video at once.

 

[Biojex]

Yeah, get this and finally add to the fun in this thread. Hate waiting but I'm just a bit ____ in wanting to take all my pics and video at once.

Can't wait!

 

[The Josh]

Can't wait!

Thank ya! Looking forward to posting it for you all.

 

[Firebird]

My exclusive has shipped and will be here next Thursday.

Congrats!

Same here.

 

[The Josh]

Congrats!

Same here.

Back @ ya

 

[Nicbot]

I wish they had done the same packaging as the Mark 1 2 3, it would look really nice

 

[LipSmack]

looks like Ikea Dioder but the puck style in the base.
Not accurate but nice still.. if he had 4 of the HT base instead it would really make this work even better

I know you and me have 4 of them lol I'm stealing this guys design but using the ht bases

 

[soubido]

mine shipped today from sideshow! cant wait!!