toylion
Super Freak
You're better off heating up the neck, blow dryer or hot water. Petroleum lubricates can cause chemical damage over time.
Hot Toys - Iron Man 2:Mark IV Limited Edition spec
- Thread starter wookster
- Start date
Help Support Collector Freaks Forum:
You're better off heating up the neck, blow dryer or hot water. Petroleum lubricates can cause chemical damage over time.
bandito
Super Freak
HT do lubrication on shoulder joints too..... I like to use vaseline...
toylion
Super Freak
There was a post on RoboCop and what happened to the sockets when vaseline was used. Not a pretty picture.
Centurion
Super Freak
Hell yeah! Didn't even see that the first time around!He could do with some hand's first
Finally got this guy yesterday (great Valetines present to myself, I love me!) Its really a well done figure! Not too much wrong with him. One of the back flaps won't stay down all the way, and one of the anti-missile pods on with waist keeps popping open, but other than that, hes all good. I did manage to scratch up his shoulder pad on one of the air flaps when trying to put him in a flying pose. Luckily the figure is suppose to look like he's alread a little dinged up, so it doesnt look so bad. Typical me.
Ricardofeitoza
Super Freak
NeXT time use jonhson's KY. It is water based. No harm to tour Iron Man!
hey friends
I've read about the problems of the flaps of his legs. are very difficult to open without breaking.
I have managed to solve in my shape.
I only have 1 blocked flap, the other opens Perfectly, very soft
to open the flap, first you have to slide back and then lift
because we have to remove the flap. when you slide the flap back. there comes a time to stop it. if your strength a little back. out the entire piece
you just have to sand the top edge and bottom edge.
the problem is that the piece that slides. is painted and hard slips
now open and close the flaps. whenever I wish
not if I try to explain good photos
I've read about the problems of the flaps of his legs. are very difficult to open without breaking.
I have managed to solve in my shape.
I only have 1 blocked flap, the other opens Perfectly, very soft
to open the flap, first you have to slide back and then lift
because we have to remove the flap. when you slide the flap back. there comes a time to stop it. if your strength a little back. out the entire piece
you just have to sand the top edge and bottom edge.
the problem is that the piece that slides. is painted and hard slips
now open and close the flaps. whenever I wish
not if I try to explain good photos
Photo's would help. No offense, but I couldn't understand a word you said.
damn translator!
damn language!I'll make photo now
morbidaj
Super Freak
- Joined
- Dec 11, 2005
- Messages
- 713
- Reaction score
- 3
There are no guns or hands on it. You guys big Jay Leno fans as well ?
Hell yeah! Didn't even see that the first time around!
snappahead
Super Freak
- Joined
- Feb 12, 2011
- Messages
- 3,256
- Reaction score
- 4
Just unboxed mine. Amazing looking figure, but I'm almost afraid to touch it. Feels so fragile. I have a lot of little paint issues here and there, but I'm keeping it. I can tell it's going to be the same on all of these. Theyr'e not too glaring until you really look close. Fingerprint magnet too! Geez, a real beauty, but I'm putting him on the shelf and leaving him alone.
Odowankenobi
Super Freak
I just got mine. Words cannot express the awesomeness. I was a defender of the original Mark III, but the Mark IV just makes it look so wrong. I can't believe how far collectibles have come in such a short time.
I spotted these 1/6 scale cocktails on ebay from this seller, and I couldn't resist getting them for Tony. 
Last edited:
Agentofchaos
Super Freak
That cocktail can also be used for the Chris Taylor figure
Odowankenobi
Super Freak
Hehe. I had a similar thought, only I'm using a martini glass from one of the James Bond figure.
Lejuan
Super Freak
I know what you mean, this is my first 'armoured' figure from HT and I haven't yet been game enough to see how far the articulation is designed to go. But I want to put it through its paces, otherwise I may as well have just bought a statue
Odowankenobi
Super Freak
I was doing a little photography and came up with this:
Similar threads
