Hot Toys MMS 145 - Iron Man 2 - Mark V 1/6 limited edition collectible specs + pics

[dedguy]

Not me. I don't think weight adds anything other than weight which is pretty worthless to me in this case. If anything it's a negative.

 

[amusedjester]

Went to CSC today and they gave me a new one.. Definitely happier I don't have to look at that faded bicep. He will be joining the rest of the armor. Need to re-arrange them again. happy times.

 

[HotKing]

I posed my Tony Stark with him carrying the suitcase...anything heavier for the suitcase will be bad...

 

[jayveeeusebio]

Went to CSC today and they gave me a new one.. Definitely happier I don't have to look at that faded bicep. He will be joining the rest of the armor. Need to re-arrange them again. happy times.

Glad yours had been replaced.

 

[amusedjester]

Salamat jay!

 

[Gully Foyle]

I'm having the hardest time getting that middle square armor piece back on the "elastic" section. Any hints / suggestions?

It's a bizzachi, eh?

I used the "function tool" to function the entire assembly off, then removed the spring ("elastic" is just eng-rish), and had Jarvis use the gantry to replace the whole flamin' thing.

 

[Gully Foyle]

Anyone else think the suitcase should've been heavier?

Nope.

Just yer mom.

________

 

[-jay-]

By the way how hard do you have to pull up to get the bottom section of the waist to pop and move? it seems really stiff and i don't wan't to break it

Anyone? did yours move easy or not? I couldn't get the bottom part to pop up.

 

[Butters]

You have to use a bit of force, but don't go carzy. It makes a click when you do it right, just like the IV and VI.

 

[-jay-]

You have to use a bit of force, but don't go carzy. It makes a click when you do it right, just like the IV and VI.

I'll have another go when i get home but didn't want this to happen.

 

[Uncanny Web-Slinger]

Took me a good few minutes of slowly titlting and pulling each side of the waist to dislodge it the first time.

 

[-jay-]

Took me a good few minutes of slowly titlting and pulling each side of the waist to dislodge it the first time.

That's good to know! thanks for the reply.

 

[Butters]

I'll have another go when i get home but didn't want this to happen.

Nah, that's what you'll look like if you break it.

It's just a little bit tighter than the IV and VI.

 

[-jay-]

Nah, that's what you'll look like if you break it.

More like.

 

[Uncanny Web-Slinger]

That would make such a killer dio or comiquette

(SSC you suck for not doing UC)

 

[Butters]

More like.

Did you get everything working like it should?

Nothing broken?

 

[-jay-]

Did you get everything working like it should?

Nothing broken?

I've not finished work yet and now my HT Batman Bruce Wayne just came so i'll be busy with that tonight.

 

[luke314pi]

This figure was definitely worth the wait.

I tried putting my custom BD Mark III on the shelf as well, but it got too crowded. I will have to find somewhere else to put him until Monger comes out.

 

[-jay-]

I tried putting my custom BD Mark III on the shelf as well, but it got too crowded. I will have to find somewhere else to put him until Monger comes out.

That's a really great display.

 

[morbidaj]

my non battledamaged left arm also has a spot on the back that is non glossy. had I not read about it in the thread I may not have noticed (until later when I did more in depth poses).. but now I am obsessing over it.

Ill check with sideshow.. incase they have one that I can swap out. the going rate on ebay seems to be 38$.

On a side note, the little flaps really are fragile. It seemed the paint on one of my fists had stuck to the flap.. so that when I pulled the fist off the LED stump, the flap came with it.

One of the handcuffs was also off the little chain. Was this how it came for everyone else? if not.. I can loop it back on.. but ill need some really thin tweezers.